项目创意

用esp8266代替Arduino的实现方法

字号+ 作者:duino123.com 来源:未知 2016-04-27 12:55 我要评论( )

用esp8266代替Arduino的实现方法








ESP8266代替Arduino解决方案

So this Lazy Old Geek (L.O.G.) heard about this ESP8266 IC. Basically, it’s a microcontroller that does WiFi. There are many Instructables with this chip and many with an Arduino. But most of these are using the ESP8266 as a sensor/WiFi connected to a standard Arduino.

Well, what I wanted to do was use the ESP8266 as an Arduino without having to use a standard Arduino.

The ESP8266 is a microcontroller similar to the AtMega328 used in the standard Arduino, e.g., Arduino UNO.

Now there is already a lot of information on doing this but I found it confusing, hard to figure out, sometimes misleading so I hope to simplify and clarify the process.

Special thanks to Lady Ada, Adafruit and the Adafruit HUZZAH ESP8266 breakout module. As usual she provides thorough, useful information.

Also, much of my information comes from this website:

https://github.com/esp8266/arduino

There are many versions of ESP8266s. Some of the cheaper ones are ESP-01, ESP-03. I think right now they go up to ESP-12. Plus there are other variations.
 

Step 1: 硬件问题

















Most communications with the ESP8266 is serial. Most computers use USB to serial converters, like FTDI chips.

问题The ESP8266 IC requires 3.3Vdc instead of the more common 5Vdc. Also, it may need up to 250mA of current.

解决1: So some ESP8266 modules have built in 3.3Vdc regulators and are compatible with 5Vdc USB to serial devices.

解决2: So many FTDI converters have the option of converting logic to 3.3Vdc. And most have a 3.3Vdc supply. The problem is that most of the power supplies are in the FT232 IC and are only capable of supplying about 50mA of current. (see picture) This is also true of the PL2303 serial converters that I use a lot of.

So a separate 3.3Vdc power source is needed.

问题: The ESP-01 module has 2x4 header that is not compatible with breadboards.(see first picture)

解决: I took some long lead female headers and bent them with a little S-curve so that they will fit in a breadboard. (see pictures)

问题: The ESP-03 module has 2mm spacing on connectors which are not compatible with 0.1” breadboards.

解决: I have some 2mm headers so I soldered some male pins to the ESP-03. (see picture), then I took some 2mm female headers and wired them to some 0.1” headers. In this case I soldered them to a 2x4 headers so that I could plug them into the connector for the ESP-01.

Well, this works pretty good for breadboarding. (see picture) but I wanted something more permanent so I may make it into a PCB.
 

Step 2: ESP8266代替Arduino





Okay, there are many articles on how to do this. Most are very confusing. One of the better ones is:

https://learn.adafruit.com/adafruit-huzzah-esp8266-breakout/using-arduino-ide

The one I used the most is:

https://github.com/esp8266/arduino

ESP8266要求

硬件:

3.3Vdc supply 250mA or greater. I used an AMS1117 3.3 regulator. This is powered by USB 5V. (The USB requirement is that the 5Vdc has a minimum 500mA of current.)

USB to Serial 3.3Vdc. I use a PL2303 device.

******************************************************************************

注意: Some newer PL2303 modules have 5Vdc on TX. This could damage the ESP8266 modules.

******************************************************************************

软件:

Arduino Environment v 1.6.4 or greater

ESP8266设置

软件:

These are instructions from https://github.com/esp8266/arduino

Installing with Boards Manager

Starting with 1.6.4, Arduino allows installation of third-party platform packages using Boards Manager. We have packages available for Windows, Mac OS, and Linux (32 and 64 bit).

Install Arduino 1.6.4 (or greater) from the Arduino website. Start Arduino and open Preferences window. Enterhttp://arduino.esp8266.com/package_esp8266com_ind... into Additional Board Manager URLs field. You can add multiple URLs, separating them with commas. Open Boards Manager from Tools > Board menu and install esp8266 platform (and don't forget to select your ESP8266 board from Tools > Board menu after installation).

连接:

ESP-01

UTXD RXD of USB-Serial

CH_PD 3.3V

Reset Pushbutton to Gnd

URXD TXD of USB-Serial

GPIO0 Pushbutton to Gnd

GPIO2

GND GND

提示: Make sure TX from serial goes to ESP-01 URXD and RX goes to UTXD

On my breadboard setup, instead of pushbuttons, I used two pin jumpers.

步骤:

Connect USB-serial to PC and ESP-01, connect power if separate

Start Arduino 1.6.4

Select ‘Tools’ ‘Port’ whatever # your USB-serial is on

Select ‘Tools’ ‘Board’ ‘Generic ESP8266 Module’

Select ‘Tools’ ‘CPU Frequency’ ‘80MHz’ Not sure why

Select ‘Tools’ ‘Flash Size’ ‘512K (64K SPIFFS)

Select ‘Tools’ ‘Upload Speed’ ‘115200’ Some ESPs may be 9600

Put ESP8266 into Flash mode:

Ground GPIO0

Briefly ground Reset

Release GPIO0

(If you have an LED on GPIO0, it should be about ½ intensity)

Load a sketch. (You can use Blink if you change it from D13 to D2)

If it works, In the Arduino environment bottom window, you will see a string of red dots as it is programming.

提示: While the sketch is programming, the blue LED on the ESP-01 will flash. If you have an LED on GPIO0, it will turn off when programming is complete.

So if you’re lucky and followed my instructions you should have successfully programmed the ESP-01 with Arduino

For the ESP-03, you would expect the same procedure to work but not quite.

First you have to connect a 10K resistor from GPIO15 to ground.

Second it doesn’t have an easily accessed Reset pin.

Well, I did some research and apparently the CH_PD pin when pulled to GND will work as a Reset.

连接:

ESP-03

UTXD RXD of USB-Serial

CH_PD 1K resistor to 3.3V

CH_PD Pushbutton to Gnd

URXD TXD of USB-Serial

GPIO0 Pushbutton to Gnd

GPIO2

GND GND

GPIO15 10K to ground

Put ESP8266 into Flash mode:

Ground GPIO0

Briefly ground CH_PD (Reset)

Release GPIO0

(If you have an LED on GPIO0, it should be about ½ intensity)

So this also works for the ESP-01.

Here is a schematic of my breadboard setup.

Step 3: 固件

What I discovered was that loading sketches overwrites the original software which is used by many of the basic Instructables and probably with a lot used when the ESP8266 is connected to a standard Arduino.

So I needed a way to reflash it back to ‘original’ software.

The one I use is ESP8266_flasher.exe

https://drive.google.com/file/d/0B3dUKfqzZnlwVGc1YnFyUjgxelE/view?pli=1

This is on Google Drive. Up at the top there is a little icon down arrow that will say Download. Load it to your PC.

Now there is a version of firmware there but it’s not the latest.

Official version?

https://drive.google.com/folderview?id=0B_ctPy0pJuW6d1FqM1lvSkJmNU0&usp=drive_web&tid=0B3dUKfqzZnlwRjFaNTUzZFptbzg

Again, this is Google Drive.

What I did is click on 0.952 support Smar

Then click on v0.9.5.2 AT Firmw

Then click on Download and save it to your PC remembering where it is.

步骤:

Run ESP8266_Flasher

Click on ‘Bin’ , select bin file

Select correct COM port

Now setup ESP8266 into flash mode as above.

Click on ‘Download’

Program should start Writing. This takes a while

Says Leaving… Failed to leave Flash mode

Ignore message, should be finished.

Test

Easy way to Test is to use Arduino, select port, open serial monitor

Set it to 115200 baud rate and Both NL & CR

On command line enter AT+RST

提醒: I just noticed it says SPI Speed: 40MHz,( though crystal is 26MHz)

On command line enter AT+GMR

SDK version: 0.9.5

Step 4: 总结



So this seems to work pretty reliably.

You don’t have to load a bootloader onto the ESP8266.

It does seem to take a little longer to program/flash.

It’s a little harder to set it up for flashing. But I’m looking into automating some of that with an FT232 module. (My old USB-BUB doesn’t work anymore.)

I need to explore some of the WiFi capabilities of the ESP8266.


如需更详细资料,如有好资源分享,请加入QQ交流群:214461008

欢迎阅读,欢迎转载,不用注明出处!本站只提供入门和进阶资料,做您学习的小伙伴!

老司机也欢迎光临指导!有好内容请加群:214461008 不要看声明了,看内容吧!

相关文章
  • 利用电视遥控器控制Arduino

    利用电视遥控器控制Arduino

    2016-05-13 17:27

  • ESP8266 Arduino气象站

    ESP8266 Arduino气象站

    2016-04-28 18:44

  • 简化到不能再简化的Arduino

    简化到不能再简化的Arduino

    2016-04-28 16:50

  • 10块钱成本自制Arduino淘宝商家别怪我

    10块钱成本自制Arduino淘宝商家别怪我

    2016-04-28 16:24

网友点评
Arduino